Pool Pump Repair · St. George, Washington, Ivins, Santa Clara, Hurricane
Pool Pump Repair in St. George, UT
As of September 2026, pool pump repair in the St. George, UT area typically costs $100–$700, averaging around $350 — a full pump replacement, installed, averages $1,300.
St. George Elite Pools · St. George, UT · phone line live at launch · Updated September 22, 2026
The pump is the pool's heart — when it fails, everything downstream (circulation, filtration, chemical distribution) stops with it. This page covers the symptoms that usually mean a pump problem, what repair typically costs in the St. George area, and how to decide between a repair and a full replacement.
Common pump symptoms and what they usually mean
- Pump hums but won't start. Almost always a failed capacitor or a seized/stuck shaft — both are repairs, not replacements. A technician can usually confirm this with the pump apart in a few minutes.
- Grinding or screeching noise. Points to worn bearings. Left alone, worn bearings eventually take the motor with them, turning a cheap bearing swap into a motor replacement.
- Water pooling under the pump housing. A leaking shaft seal — a low-cost part, but one that needs the pump opened to replace, so it's priced as labor plus a small part.
- Pump runs but weak or no flow. Often a clogged impeller, a closed valve, or air getting into the system through a loose union or a low pool water level — not always the pump itself.
- Pump trips the breaker repeatedly. An electrical fault inside the motor, or a wiring issue outside it — this one is worth a same-visit electrical check rather than repeated breaker resets.
Pool pump repair cost in St. George
Repair pricing depends on the failed part. Overall, pump repair runs $100–$700, averaging $350.
| Item | Typical range | Source |
|---|---|---|
| Repair (overall) Most repairs land near $350. | $100–$700 · avg $350 | Angi 2026 (national pool pump repair range) |
| Motor repair | $200–$500 | Angi 2026 (national) |
| Motor replacement only | $350–$700 | Angi 2026 (national, motor only, wet end reused) |
| Seal replacement | $100–$250 | Angi 2026 (national) |
| Impeller repair | $120–$300 | Angi 2026 (national) |
| Impeller replacement | $150–$400 | Angi 2026 (national) |
| Bearing replacement | $150–$350 | Angi 2026 (national) |
| Electrical repair | $100–$250 | Angi 2026 (national) |
Repair vs. replace
A repair makes sense when a single component has failed on an otherwise sound pump — a capacitor, a seal, bearings. Replacement starts to make more sense when the motor itself has failed on an older pump, or when repair costs start closing in on what a new pump would cost installed.
| Item | Typical range | Source |
|---|---|---|
| Full replacement, installed (all types) | $700–$4,000 · avg $1,300 | Angi 2026 (national, installed), average $1,300 |
| Single-speed pump, unit only | $250–$1,000 | Angi 2026 (national, unit only) |
| Variable-speed pump, unit only | $800–$2,500 | Angi 2026 (national, unit only) |
| Install labor, same brand/HP swap | $200–$200 | Angi 2026 (national, same brand/HP swap) |
| Install labor, different brand/rewiring | $280–$500 | Angi 2026 (national, different brand, rewiring/new pipe) |
A variable-speed pump costs more upfront than a single-speed model but runs quieter and more efficiently across a long St. George pool season — worth asking about if you're replacing rather than repairing.
Why St. George pumps fail sooner than the national average
Two local factors matter more here than in most markets. St. George's pool season runs roughly April through October, so a pump here logs more annual run-hours than one in a shorter-season climate — and run-hours are the single biggest driver of bearing and seal wear. Hard local water (roughly 342 ppm) can also contribute to mineral buildup inside the pump housing over years of service, which is worth mentioning to a technician if your pump is older.
Get matched with a local pump repair company
Tell us what your pump is doing and we'll connect you with an independent local company. See also the pool repair page for heater and leak issues, and the full repair cost guide for every component's pricing in one place.
Common Questions
How much does pool pump repair cost in St. George?
$100–$700, averaging around $350, as of September 2026 — the specific part (capacitor, seal, bearings, impeller) determines where in that range a repair lands. Full component pricing is on our pool repair cost guide.
Should I repair my pool pump or replace it?
Rule of thumb: if the repair estimate runs past roughly half of what a new installed pump costs, replacement is usually the better long-term value. At a $100–$700 repair range against a $1,300 average installed replacement, a repair quote above roughly $650 is worth comparing directly against a replacement quote — especially on an older single-speed pump nearing the end of its service life anyway.
Why do St. George pool pumps wear out faster than average?
St. George's long hot season (roughly April through October) means pumps here log more annual run-hours than in milder climates, which is the single biggest driver of bearing and seal wear regardless of brand. Hard local water can also accelerate mineral buildup inside the pump housing over time.
Can I run my pool without a working pump?
Not for long. Without circulation, chlorine stops distributing evenly, algae can take hold within days in St. George's heat, and a pool that sits stagnant during summer temperatures can go green fast. Treat a dead pump as a near-term priority, not a wait-and-see item.
Does St. George Elite Pools repair pool pumps?
No. St. George Elite Pools is an independent referral service — we connect you with independent, local St. George-area pool repair companies. We don't perform repairs ourselves.
Get Matched With a Local Pool Pro
Tell us what's going on and your city — we'll connect you with an independent pool cleaning or repair company that covers it.
Form opens at launch — this preview shows the fields and consent language as built.